Nitro Rustler

This is the Traxxas Servo Case for 2055 servo. This is Traxxas part number 2052.

This is the Digital High Torque Traxxas Servo. FEATURES:Ball bearingsBlack plastic construction INCLUDES:One digital high torque ball bearing servo SPECS:Ratings such as speed and torque have not been provided by Traxxas.Length: 2.16" (55mm)Width: .78"...

This is the Traxxas 5x11x4mm Ball Bearing Set.  This includes eight ball bearings.  These are used in many of the Traxxas vehicles. FeaturesMade of Stainless steelShielded on both sides (not rubber sealed) Includes8 ball bearings Specs5mm...

This is a set of Traxxas TRX 3.3 Cooling Head Gaskets measuring 0.20, 0.30, and 0.40mm. The stock size is 0.30mm. These will give you the ability to tune your engine for optimal performance under your conditions.Fits TRX 3.3 engines in:Nitro 4-TecNitro...

This is the Traxxas Replacement Idler Gear and Shaft for the Nitro Stampede/Rustler. This gear is located in the transmission. Features: White nylon construction Steel shaft Includes:One 20 tooth idler gearOne idler gear shaft Specifications:Gear outer...

This is the Traxxas Black Antenna Tube with Cap and Wire Retainer.  These are compatible with nearly all Traxxas cars, trucks and boats.  The sleek black design looks great as well.

This is the Traxxas TRX 2.5 & 3.3 Engine Backplate 20x1.4mm O-Ring, part number 5213.

This is the Traxxas EZ-Start 1 Quick Connector Stock Replacement Wiring Harness. Features: All wires included in an EZ starting system Includes:One complete wire set with connectorsTwo zip tiesOne adhesive foam pad Requires: The remainder of the EZ...

This is the optional Blue Traxxas Resonator Dyno-Tuned Performance Pipe for the Traxxas Jato, Nitro Rustler and Nitro 4-Tec with TRX Racing Engines. FEATURES:The Traxxas Resonator aluminum tuned pipe is specifically engineered to fit right in the...

This is Traxxas Rod Ends Short Hollow Balls Set of six short rod ends with hollow ball connectors Replacement Part For4-Tec 2.0 AWD Chassis4-Tec 2.0 VXL AWD ChassisBandit VXLBanditBIGFOOT No. 1 Officially Licensed ReplicaChevrolet Corvette StingrayDrag...

This is the Traxxas Complete Stock Replacement Carburetor for the Traxxas TRX 2.5 and TRX 3.3 Engines.  A damaged carburetor will severely decrease the power of your engine.  This can restore the lost power.  The...

This is a Traxxas Hard Chrome Suspension Pin Set with E-clips. These are used on the Nitro Rustler, Nitro Slash, Nitro Sport, and Nitro Stampede trucks.Includes:2 - 24X3mm pins4 - 31.5X3mm pins2 - 40X3mm pins2 - 48X3mm pins10 - 3mm e-clips

This is the EZ Start 2(R) Starting System from Traxxas. This is the updated replacement for the first-generation EZ Start 2 System. It features a higher torque motor for the new 3.3 race series engines. FEATURES:Simple push-button starting for glow plug...

This is the Traxxas Spring Pre-Load Spacers Change the ride height on your vehicle with these spring pre-load spacers for Traxxas Ultra Shocks. Set includes the following spacers: 1 mm (2), 2 mm (2), 4 mm (2), and 8 mm (2). Replacement Part ForBandit...

This is the Traxxas Multi-tool (plastic) The plastic multi-tool can be used to loosen castle nuts as well as upper and lower shock caps. Replacement Part ForE-Revo VXL BrushlessHoss 4X4 VXLJatoRevoRustler 4X4 VXLRustler 4X4Slash 4X4 UltimateSlayer Pro...

This is an optional Traxxas Large Knurled Flywheel for use with Starter Boxes. Features: Large knurles to be gripped by rubber starter wheels Two pin aluminum construction Vent holes drilled to keep clutch shoes cooler Includes: One 40mm...

This is the Traxxas replacement piston and sleeve for the TRX Pro .15 engines. Features: ABC (Aluminum piston with a Brass sleeve or liner that is Chrome plated) Matched set with oil ring Includes:1 Piston1 Sleeve (liner)

This is a pair of Traxxas Front Suspension Arms for the Bandit, Nitro Rustler, and Nitro Stampede.SpecificationsLength: 3"Width: 1.2"FitsBandit VXLBandit XL-5Nitro RustlerNitro SportNitro Stampede

This is the Traxxas Slipper Tension Spring with Spur Gear Bushing and Locknut.Includes:Slipper tension spring (1)Spur gear bushing (1)4mm Locknut with nylon insert (1) FitsBandit XL-5E-MaxxNitro RustlerNitro SlashNitro SportNitro StampedeRustler...

This is the Traxxas Bellcrank Bushings (Plastic) set (5x8x2.5mm) (4) Includes: Set of four 5x8x2.5 mm bellcrank bushings

These are hardened steel drive yokes for the Traxxas Rustler and Stampede. FEATURES:Hardened steel construction and is stronger than stock parts.These yokes also come with U-Joints pre-installed for ease of installation. INCLUDES:Two hardened steel yokes...

This is a pair of 2.8" Twin-Spoke Rear Wheels for the Traxxas Jato 2.5 and 3.3 trucks.  These are stock replacement wheels.FEATURES: Nylon constructionChrome platedFive split spoke wheel patternUses 12mm hex adapterINCLUDES: Two Rear Chrome Wheels

This is a Package of Replacement Cush-Drive Elements for the EZ Start 2 System. FEATURES:Black plastic construction INCLUDES:Four cush-drive elements REQUIRES:The remainder of the EZ Start 2 system. SPECS:Length: 6mm (0.24")

This is a Traxxas TRX 2.5 and 2.5R Piston and Sleeve kit.  If you have several gallons of fuel through your engine, it may be time for a new piston and sleeve.  It is a direct replacement.  Included are one piston, one...

This is the Traxxas Front Bulkhead (Black) Replacement black composite front bulkhead Replacement Part ForBIGFOOT No. 1 Officially Licensed ReplicaBigfoot Officially Licensed ReplicaDrag Slash 1967 Chevrolet C10 TruckDrag Slash Ford Mustang 5.0Ford F-150...

This is the Replacement EZ-Start 2 Housing Set with Hardware and Motor Bushing. Includes(5) 3x12 mm screws (1) 3x20 mm screwMotor Bushing Replacement Part ForJatoNitro RustlerNitro SlashRevoSlayer Pro 4X4T-MaxxTRX 2.5RTRX 3.3

This is the Traxxas Assembled Tuned Pipe Tuned pipe comes assembled and ready to install on Nitro Rustler, Nitro Sport, and Nitro 4-Tec with TRX 2.5 engine. *For TRX 2.5 - Requires Coupler Part #5246*For Pro.15 - Requires Coupler Part #4451 Replacement...

This is the Hot Racing Aluminum 90mm Heavy Duty Big Bore Shocks (2pcs) 90mm big bore threaded body aluminum shocks for many 1/10th scale off-road vehicles using 90mm shocks. Some applications include, but are not limited to: Traxxas Bandit front, Nitro...

These are the Traxxas XX-Long Titanium-Nitride Coated Hardened Steel Shock Shafts. Each package includes two shocks shafts. These XX-long hardened steel shafts have a super tough titanium nitride coating with a micro-polished finish for smoother...

This is a pair of Traxxas Front White Springs. These fit the front long Ultra Shocks (3760A) on many Traxxas vehicles.Fits:Bandit VXLBandit XL-5Nitro RustlerNitro SlashNitro SportNitro StampedeRustler VXLRustler XL-5Slash 2WD VXLSlash 2WD XL-5

These are the Traxxas Hardened Steel Titanium-Nitride Coated Shock Shafts. These are an excellent upgrade for many Traxxas vehicles.Includes: Two shaftsSpecificationsDiameter: 3mm (0.118")Length: 47 mm (1.85")Thread: 3mm (0.118") Accessory Part ForHoss...

This is the RPM Black Front Shock Tower for the Traxxas Nitro Slash, Nitro Rustler, and Nitro Sport trucks.RPM shock towers for Traxxas 1/10th scale trucks are designed to add strength and support to the front-end suspension components of these great...

This is the RPM Blue Front Suspension A-Arm Set for the Electric Bandit, Nitro Rustler, Nitro Stampede, and Nitro Sport vehicles.RPM Rear A-arms for the Traxxas Bandit, Nitro Rustler, Nitro Stampede, and Nitro Sport are finally here to strengthen the...

This is a pair of Traxxas 2.2" Rear Lite Truck Wheels (white) for the Jato trucks, as well as the electric Rustler and electric Stampede.  These are 2.2-inches in diameter, have a 12mm hex, and require 2.2" tires. ...

This is the Traxxas Rubber Exhaust pipe Rubber exhaust pipe for Nitro Rustler, Nitro Sport, and Nitro 4-Tec. (Side Exhaust Engines Only) Replacement Part ForTRX Pro .15Nitro Rustler Nitro Sport Nitro 4-Tec

This is the Traxxas aluminum (Red Anodized Shock Caps Shock caps, aluminum (Red-anodized) (4) (fits all Ultra Shocks)Aluminum shock caps are great way to boost the durability and style of any Traxxas vehicle equipped with Ultra Shocks. The machined caps...

These are the Traxxas Flanged and Serrated Nuts, Aluminum (4mm) (Orange-Anodized) (4) Lightweight and great looking, these 4 mm anodized aluminum flanged lock nuts are the perfect finishing touch for your vehicle. The serrated flange and nylon locking...

These are the Traxxas X-Long Titanium-Nitride Coated Hardened Steel Shock Shafts. Each package includes two shock shafts.For use with X-Long shocks on:1/10 Monster Jam Trucks1/10 RallyBandit VXLBandit XL-5CraniacNitro RustlerNitro SlashNitro SportNitro...

This is the Traxxas aluminum (Orange Anodized Shock Caps Shock caps, aluminum (orange-anodized) (4) (fits all Ultra Shocks)Aluminum shock caps are great way to boost the durability and style of any Traxxas vehicle equipped with Ultra Shocks. The machined...

These are the Traxxas Stainless Steel Suspension Hinge Pins with E-Clips. This set fits the Nitro Rustler, Nitro Slash, Nitro Sport, and Nitro Stampede trucks.Includes:48mm Rear inner hinge pin (2)31.5mm Front and rear outer hinge pin (4)39mm Front...