Nitro 4-Tec

This is the Traxxas Heat Shield Tubing for Fuel Line (2) Fiberblass heat shield tubing Replacement Part ForJatoNitro RustlerNitro SlashRevoSlayer Pro 4X4T-MaxxTRX 2.5RTRX 3.3

This is a set of Traxxas 10x15mm Ball Bearings for use on the Traxxas Revo and other vehicles. Features: Steel Construction Shielded with blue rubber seals Includes: Two Ball Bearings Specifications:Inner Diameter: 10mmOuter Diameter: 15mmSide...

This is the Replacement Servo Saver with Adapters. The spring-loaded servo saver protects your steering servo by absorbing shocks that might otherwise cause internal gear damage. Replacement Part ForBandit VXLBanditFord F-150 RaptorFord F-150 RaptorNitro...

This is the Traxxas aluminum blue-anodized shock caps Aluminum shock caps are great way to boost the durability and style of any Traxxas vehicle equipped with Ultra Shocks. The machined caps fit precisely and hold tightly, run after run, jump after jump...

This is the Traxxas 4-Cell AA Battery Holder with On/Off Switch for use to power the receiver and servos in nitro vehicles.FitsNitro 4-TecNitro RustlerNitro SlashNitro SportNitro StampedeS-MaxxSportmaxxT-Maxx 2.5T-Maxx 2.5RT-Maxx 3.3

This is the Traxxas 1200mAh NiMH 5-Cell 6-Volt Hump Pack Receiver Battery for Traxxas Nitro vehicles.  This high quality 5-cell hump pack uses proven nickel-metal hydride cells and is rated at 1200mAh.  Fully charged, it provides about 1 hour...

This is a set of Traxxas Long Rod Ends with Hollow Ball Connectors. Each package contains six rod ends and six hollow balls.Fits1/10 Monster Jam Trucks1/10 RallyBandit XL-5CraniacE-MaxxNitro 4-TecNitro RustlerNitro SlashNitro SportNitro StampedeRustler...

This is a Traxxas High Stall Clutch Set for the Traxxas T-Maxx .15, 2.5, 3.3, Revo 2.5 and 3.3 trucks.  A higher stall lets you rev the engine up higher before the clutch engages, for more power when you are taking off.

This is a Traxxas EZ-Start 2 Replacement Motor and Pinion Gear.  This is used on vehicles like the T-Maxx 2.5, 3.3, Revo 2.5, 3.3, Jato, Nitro 4-Tec, Nitro Rustler, Nitro Slash, Slayer Pro, and other vehicles using the 2.5 and 3.3 engines...

This is the Traxxas Wheel Hubs hex (blue-anodized, lightweight aluminum) (2)/ axle pins (2) These 12 mm aluminum hex wheel hubs are both lightweight and tough as nails with brilliant blue anodizing. *Includes axle pins (2) Accessory part forDrag Slash...

This is the Traxxas Glow Plug Lead Wire for the Revo EZ Starting System. This attaches to the glow plug prong to heat the plug during starting. Features: Blue silicone insulated wire with pre-installed connectors Includes:One glow plug wire leadOne...

This is the Traxxas Hex Wrench Set with 1.5mm, 2mm, 2.5mm, 3mm, and 2.5mm ball wrenches. Whether you have a Slash, Revo, E-Maxx, Summit, or something else, these are a must-have set of wrenches for Traxxas owners!

This is a Tube of White Lithium Grease from Traxxas. This product can be used to lubricate parts, such as gears. FEATURES Great lubrication for nylon gears INCLUDESOne tube of lithium grease (volume unknown) REQUIRESApplication to parts needing...

This is a Traxxas Jato 2.5, 3.3, and T-Maxx 3.3 Antenna Crimp Nut and Antenna Nut Wrench.  This includes the antenna crimp nut and the wrench.

This is a pair of Traxxas Throttle Dust Boots and a Return Spring for use on the carburetors of the TRX 2.5, 2.5R, and 3.3 nitro engines.Fits:Jato 2.5 & 3.3Nitro 4-TecNitro Rustler 2.5Nitro SlashRevo 2.5 & 3.3SlayerT-Maxx 2.5 & 3.3

This is the Traxxas Auto-Detectable Smart Temperature Sensor. This plug-and-play sensor is designed for use with the Traxxas 6550 Telemetry Expander. The auto-detectable temperature sensor plugs into the optional TQi Telemetry Expander to provide...

This is a set of four Traxxas Green-Anodized Aluminum 4mm Lock Nuts with a Flanged and Serrated surface.Features May be used in any application requiring this size locknut Serrated rear section ensures sure grip Includes: Four 4mm Flanged...

These are Traxxas 3x12mm Button Head Screws (6). Features: Steel Construction Black in color Hex head Includes: Six button head screws Specifications:Length: 12mm (.47")Diameter: 3mm (.12") Replacement part for1/16 E-Revo VXL1/16 E-Revo1/16...

This is the Traxxas 4 AA Battery Holder for Receivers in Nitro vehicles like the Jato, Nitro Rustler, T-Maxx, and others. Jato 4 AA battery holder with Futaba-style connector. No On/Off switch.Includes: One 4 cell AA Battery Holder w/Receiver Connector...

This is the Traxxas Red Aluminum Antenna Crimp Nut with Nut Wrench, for use on many Traxxas vehicles including the Revo, E-Maxx, Jato, Slash 2WD, and T-Maxx trucks.Fits1/10 E-Revo Brushed1/10 E-Revo Brushless1/10 SummitE-MaxxE-Maxx BrushlessJato 2.5Jato...

This is the Replacement Roller Clutch for the Traxxas 2.5 and 3.3. This is located at the EZ Start end of the crankshaft. This is the One Way bearing for the EZ starter and is also used with a pull starter FEATURES:Steel construction INCLUDES:One roller...

This is the Traxxas Big Bore Shock Piston Head Set with Mounting Bushings. This set includes two 2-hole pistons, two 3-hole pistons, two shock mounting bushings, and two washers.Includes2- Pistons (2-hole)2- Pistons (3-hole)2- Shock Mounting Bushings2-...

This is a shock rebuild kit for 2 Traxxas black plastic shocks. Includes:4 E-clips2 C-clips2 O-rings8 Washers2 Diaphrams Replacement Part For4-Tec 2.0 AWD Chassis4-Tec 2.0 VXL AWD ChassisChevrolet Corvette StingrayFord F-150 Raptor R 4X4Ford Fiesta ST...

These are the Traxxas Pink Aluminum 4mm Flanged Wheel Nuts (4). These wheel nuts fit a wide variety of Traxxas vehicles. Lightweight and great looking, these 4 mm anodized aluminum flanged lock nuts are the perfect finishing touch for your vehicle. The...

This is the Long RPM Sensor from Traxxas. The RPM sensor plugs directly into your TQi receiver to provide real-time speed and RPM data while you drive. Real-time telemetry requires a telemetry magnet, TQi radio with Traxxas Link Wireless...

These are the Traxxas Collars with Set Screws. These come in packages of two.Includes:(2) screw collars(2) 3mm set screws Fits1/10 E-Revo Brushed1/10 E-Revo Brushless1/10 SummitE-MaxxNitro 4-TecNitro RustlerNitro SlashNitro SportNitro StampedeNitro...

This is the Traxxas Molex/Tamiya to Receiver Pack Charging Adapter. This adapter allows you to use a charger equipped with a standard Tamiya-style plug to charge receiver batteries.

This is the Blue Silicone Pipe Coupler for the T-Maxx 2.5 This goes between the tuned pipe and the header FEATURES:Blue silicone constructionFor use with pipes #5152 and #4452 INCLUDES:One pipe coupler REQUIRES:Installing on the vehicle with wire...

This is the Traxxas Replacement Servo Gear Set for 2055 and 2056 Servos. This is Traxxas part number 2053.

This is the Traxxas 2055 High-Torque Servo.  This has 80 oz/in of torque, making it an excellent steering servo.  This works well in the Traxxas T-Maxx, E-Maxx, Revo or any other vehicle that you would like to mount this in...

This is the Traxxas TRX Pro.15 Nitro Engine with Short Crank The TRX Pro.15 is known for its easy tuning, smooth idle, and reliable running. The Pro.15 features ABC (Aluminum piston, Brass sleeve with Chrome plating) construction, a heavy-duty connecting...

This is a set of RPM Black Snap-Tite Body Savers. One of the weakest points on a Lexan body is where the body mounts to the chassis. The holes cut in the body for the body posts have a tendency to crack and fracture. This is the reason RPM designed these...

This is the Traxxas TRX 3.3 Racing Engine with Pull Start.  This will give your Revo, T-Maxx 2.5, or Jato an unbelievable boost in performance.  This is a must have upgrade.  You can also use this with the factory EZ-Start. ...

This is the Traxxas Blue Aluminum Header for Rear Exhaust TRX 2.5, 2.5R, and 3.3 Engines on the Nitro 4-Tec, Nitro Rustler, and Nitro Slash trucks.FitsNitro RustlerNitro SlashTRX 2.5RTRX 3.3

This is a Traxxas Servo Case for 2018 servos.FeaturesReplaces top, center and bottom sections of damaged servo casesConstructed of black plasticIncludesOne Servo Case Set for the Traxxas #2018 Servo with top, center and bottom...

This is a pack of Traxxas 3x15mm Countersunk Hex Head Machine Screws. Each package includes six screws.Fits:1/10 E-Revo Brushed1/10 E-Revo Brushless1/10 SummitE-MaxxE-Maxx BrushlessFunny CarJato 2.5Jato 3.3Nitro 4-TecRevo 3.3SlayerSlayer ProT-Maxx 2...

This is the Traxxas 35mm Flywheel with Magnet for use with the TQi Radio System.FeaturesFor use with Traxxas glow powered vehiclesEquipped with a magnet that enables an RPM sensor to read RPM data IncludesTraxxas 35mm Flywheel with Magnet

This is the Traxxas aluminum (pink Anodized Shock Caps Shock caps, aluminum (pink-anodized) (4) (fits all Ultra Shocks)Aluminum shock caps are great way to boost the durability and style of any Traxxas vehicle equipped with Ultra Shocks. The machined...

This is the Traxxas High-Speed Needle Valve Assembly for the TRX 2.5, 2.5R, and 3.3 nitro engines. This includes the high speed need, fuel fitting, 2.5x1.15mm O-rings (2), and 5.3x7.8x.6mm crush washers (2).For use with TRX 2.5 & 3.3 engines used...

These are the Traxxas 3x15mm Buttonhead Hex Machine Screws. Each package includes six screws. These are used across many different Traxxas vehicles.Replacement part for1/16 E-Revo VXL1/16 E-Revo1/16 Slash 4WD1/16 Summit4-Tec 2.0 AWD Chassis4-Tec 2.0 VXL...